nesdev.com
http://forums.nesdev.com/

絵描衛門 / Dezaemon PCB scan
http://forums.nesdev.com/viewtopic.php?f=11&t=11044
Page 1 of 1

Author:  naruko [ Mon Feb 24, 2014 1:57 am ]
Post subject:  絵描衛門 / Dezaemon PCB scan

PCB class: Nintendo HVC-SXROM-01
U1 PRG-ROM: ATH-87-0 PRG, 0x20000 byte ROM, CRC32: 0xd1e50064
U2 CHR-RAM: LH5168FB-10L, 0x2000 byte RAM
U4 W-RAM: LH52A256-10LL, 0x8000 byte RAM (banked)

high resolution and other sides scan
http://www1.axfc.net/u/3179252.zip

nescartdb にはどうやって登録するの?

Attachments:
ath-87_pcb_top_low.jpg
ath-87_pcb_top_low.jpg [ 266.13 KiB | Viewed 2941 times ]

Author:  Bregalad [ Mon Feb 24, 2014 2:43 am ]
Post subject:  Re: 絵描衛門 / Dezaemon PCB scan

A third SXROM game ? Cool, I always tought there were only 2.

Does it use all 32k of SRAM ?
As far I know both Final Fantasy I & II and Best Play Pro Yakyuu Special used only 16k (both are multicard with 2 games on them I think, please tell me if I'm wrong).

Author:  naruko [ Mon Feb 24, 2014 3:24 am ]
Post subject:  Re: 絵描衛門 / Dezaemon PCB scan

デザエモンはゲームを作るソフトだ。自分はこのソフトを使ったことがないが、ユーザーに聞いたことがある。
このソフトでは4つのステージを作ることができる。4つのステージのデータは RAM の page 0,1,2,3 が Stage 1,2,3,4 になるというので、おそらくSRAM全てを使用している可能性が高い。

このユーザーは絵描衛門がエミュレータで正常に動かないと言っている。
http://dezagarou.ame-zaiku.com/html/other/ezaemon.html
Quote:
ちなみに、絵描衛門はエミュレーターでは正常に作動しません。

エディットモードで保存する事が出来ず、フリーズしてしまいます。

Author:  Bregalad [ Mon Feb 24, 2014 4:19 am ]
Post subject:  Re: 絵描衛門 / Dezaemon PCB scan

So basically as far as I can understand you, this game uses all 4 SRAM banks to allow the user to edit 4 different stages ? Sounds rather unique for a NES/FC game !

It seems current emus would emulate SNROM instead (with no SRAM banking) and crash on edit mode, as the emu refuses to switch RAM banks ?

I also see that the PRG-ROM is 28-pin so it means its size is 128kb or less, so they definitely used this board for SRAM banking solely.

Author:  Pokun [ Mon Feb 24, 2014 6:53 am ]
Post subject:  Re: 絵描衛門 / Dezaemon PCB scan

naruko wrote:
nescartdb にはどうやって登録するの?

右上隅の[Register]をクリックして、そこでログイン、パスワード、メールの情報を入れてください。すみませんがそれ以上解りません。

Naruko is asking how to register and submit to bootgod. I have never done that so I don't really know.

Author:  Bregalad [ Mon Feb 24, 2014 7:36 am ]
Post subject:  Re: 絵描衛門 / Dezaemon PCB scan

As far as I can remember you have to talk to Bootgod directly, there is no automatic process for registering. Send him a PM.

Author:  etabeta [ Fri May 02, 2014 5:30 am ]
Post subject:  Re: 絵描衛門 / Dezaemon PCB scan

@naruko: I've documented the 32k SRAM in MESS. thanks a lot!
I'm not fully sure how to verify that the saving/loading on different banks work (I hate dezaemon editor :) ), but FF1+2 works fine in MESS so I would expect this to work too...

Page 1 of 1 All times are UTC - 7 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/