Some of my own findings...
Code: Select all
Undocumented Registers ---------------------- Many of the undocumented registers work only in conjunction with ROMDIS, --> Pinouts - CPU - ROMDIS Pin FF50 - POST - Boot BIOS Disable (Write-able only once after Reset) (R/W) Bit 0 - Boot BIOS Region (0=Boot BIOS, 1=Cartridge ROM) Bit 1-7 - Not used Internally used by all BIOSes, selects whether Boot BIOS (ie. the Nintendo Intro), or normal cartridge ROM is mapped to 0000h-00FFh (on CGB additionally to 0200h-08FFh). The register can be written to only once. FF60 - JOYC - Joypad Mode (W) (enabled while ROMDIS=HIGH only) Exists on all gameboy types. Register is write-only (even when it is enabled, reading always returns FFh). Bit 0 - Joypad Mode (0=Normal/Read-only, 1=Read/Write) Bit 1-7 - Not used On older gameboys (those with 2x4bit joypad pinout), the lower 4bit of FF00h become read/write-able. On color gameboy and up (those with 8bit joypad pinout), register FF61h becomes R/W (if it is enabled by ROMDIS). Although FF60h is write-able only while ROMDIS=HIGH, the setting keeps working even after releasing ROMDIS. --- Below Registers on CGB only --- FF4C - DMG1 - CGB Mode / DMG Mode (R/W only until FF50h is written) Internally used by CGB-BIOS. Set to 04h in DMG-mode. Set to Cart[0143h] in CGB-mode (for CGB carts, that is usually 80h or C0h) (so the three read/write-able bits are usually zero in CGB mode). Settings like Cart[0143h]=88h, would allow to enter a special mode, but, in that case, the BIOS boots up with a locked blank palette, so that mode is of no good use. Bit 0 - Unknown (0=Normal, 1=No effect?) Bit 1 - Not used Bit 2 - Disable All CGB Functions (0=CGB, 1=DMG) Bit 3 - Disable Some CGB Functions (0=Normal, 1=Extended DMG Mode) Bit 4-7 - Not used Bit3 disables HDMA, BGPD, OBPD, and KEY1. Bit2 does the same, and additionally disables RP(IR), VBK(VRAM), SVBK(WRAM), and FF6Ch. If both bits are set, Bit3 has priority over Bit2. FF4Ch is write-able (and read-able) only until FF50h is written to for the 1st time. ...one or more of the bits probably affect FF02h serial-speed... ? FF6C - DMG2 - Unknown (R, or R/W, depending on FF4Ch.Bit2) Bit 0 - Whatever CGB/DMG Mode related (0=CGB, 1=DMG) Bit 1-7 - Not used Internally used by CGB-BIOS. Set to 01h in DMG mode. This register becomes read-only if FF4Ch.Bit2 has been set to 1 prior to the first write to FF50h. In other words: FF6Ch is R/W in CGB mode, and read-only in non-CGB mode. The function of the bit is unknown? FF61 - JOY8 - 8bit-Joypad (R, or R/W) (enabled while ROMDIS=HIGH only) 0 - Right (0=Low/Pressed, 1=High/Released/Disabled) 1 - Left ("") 2 - Up ("") 3 - Down ("") 4 - Button A ("") 5 - Button B ("") 6 - Select ("") 7 - Start ("") The register is normally disabled. When enabled via ROMDIS, it can be either read-only (input), or read/write (output), depending on FF60h setting. FF63 - ? - Undocumented Ext.Configuration (enabled while ROMDIS=HIGH only) This register is normally deactivated (value FFh, read-only). 0 - Unknown (0=Normal, 1=No effect?) 1 - Unknown (0=Normal, 1=Disable Video?) 2 - Unknown (0=Normal, 1=Disable Video?) 3 - Unknown (0=Normal, 1=Disable Video?) 4 - Unknown (0=Normal, 1=Disable Video?) 5 - Unknown (0=Normal, 1=Crash?) 6 - Unknown (0=Normal, 1=No effect?) 7 - Unknown (0=Normal, 1=No effect?) When ROMDIS is high, reading returns 00h, and writing non-zero values seems to crash the program (or disable video) in most cases. FF72 - Undocumented (00h) - Bit 0-7 (Read/Write) FF73 - Undocumented (00h) - Bit 0-7 (Read/Write) FF74 - Undocumented (00h) - Bit 0-7 (Read/Write) - CGB Mode Only FF75 - Undocumented (8Fh) - Bit 4-6 (Read/Write) FF76 - Undocumented (00h) - Always 00h (Read Only) FF77 - Undocumented (00h) - Always 00h (Read Only) Further undocumented CGB Registers. The numbers in brackets () indicate the initial values. Purpose of these registers is unknown (if any). Registers FF6C and FF74 are always FFh if the CGB is in Non CGB Mode.
Code: Select all
KEY0 FF4C CPU mode register Bits 2 and 3 CPU mode select 00: CGB mode (Mode used by carts supporting CGB) 01: DMG/MGB mode (Mode used by DMG/MGB-only carts) 10: PGB1 mode (STOP the CPU, with the LCD operated by an external signal) 11: PGB2 mode (CPU still running, with the LCD operated by an external signal) OPRI FF6C OBJ priority mode select register Bit 0 OBJ priority mode select (when X coordinates are different) 0: smaller OBJ-NO has higher priority 1: smaller X coordinate has higher priority
Not sure what the external LCD signal flag could be good for. It isn't R/W after booting, but it could be set via cart header.
My best guess would be that it might be for streaming video through the cart edge connector?
Don't know how that could work with the CPU kept running though.
It might work when mapping external video memory to parts of the ROM space, and running CPU code in the remaining ROM space during vblank?
That could be tested when using a ROM filled with nonzero/random data, that might display something (unless it needs palette init somehow).
The CGB feature sounds more like support for something alike coprocessors on SNES, where one could DMA data from cartridge to VRAM.
Or perhaps more ideally, completely disable internal VRAM, and instead DMA pixels directly from cartridge to the LCD hardware.
I did a quick test of OPRI on my GBC by quickly modifying a DMG project I had into a CGB ROM, but I could not get it to work. It was very hard to see on the small LCD though and there are many things that might have went wrong since I didn't properly initialize all CGB registers and stuff.
- Posts: 761
- Joined: Wed Feb 13, 2008 9:10 am
- Location: Estonia, Rapla city (50 and 60Hz compatible :P)