It is currently Mon Dec 11, 2017 9:45 pm

All times are UTC - 7 hours



Forum rules


1. NO BLATANT PIRACY. This includes reproducing homebrew less than 10 years old, with the exception of free software.
2. No advertising your reproductions, with the exception of free software.
3. Be nice. See RFC 1855 if you aren't sure what this means.



Post new topic Reply to topic  [ 3 posts ] 
Author Message
 Post subject: UNROM to UOROM
PostPosted: Sun Aug 12, 2012 7:47 pm 
Offline

Joined: Wed Feb 15, 2012 10:19 pm
Posts: 81
UNROM to UOROM
Bend up eprom pins 1, 2, 24, 30, 31, and 32.
Bend up MC74HC32 pin 3.Can be left as is.
Solder pin 1 and 24 to hole 14.
Solder pin 2 to hole 22.
Solder pin 30 to MC74HC32 pin 3.
Solder pin 32 to hole 28.

I got this from looking at tokumaru pic of his uorom test cart. Worked for me.

Edit... some games wouldn't work in cart if 24 wasn't grounded.


Last edited by proveaux on Thu Sep 06, 2012 7:45 pm, edited 2 times in total.

Top
 Profile  
 
 Post subject: Re: UNROM to UOROM
PostPosted: Fri Aug 17, 2012 11:09 pm 
Offline

Joined: Tue Aug 14, 2012 8:37 pm
Posts: 47
Thanks! I'll add it to my list of conversions.


Top
 Profile  
 
 Post subject: Re: UNROM to UOROM
PostPosted: Fri Nov 21, 2014 1:18 am 
Offline

Joined: Mon Jan 23, 2012 11:27 pm
Posts: 141
Some additional info, and then questions:

On a NES konami unrom board, the inputs for 7432 pin 3 (1Y) are
74161 Q3 (pin 11)
CPU A14 (cart edge pin 41)

On the TAITO-UNROM board used for Takeshi no Chousenjou, those two signals go to pins 4 and 5, 2A and 2B. So in that case it should be 2Y on pin 6 going to CHR A17.

And so the question: I'm trying to put the translated rom (http://www.romhacking.net/translations/1682/) on the original cart. I expanded and patched and test on a socketd NES cart and everything seemed ok. But I don't get anything after installed the eprom on the original board. Thoughts/ideas? Does this board do something else differently than the NES unrom board?
I'm assuming the prg layout is regular nintendo 128K prg, since it was a 28 pin mask rom.

wiring
pin 1 up
pin 2 -> hole 22 chr a16
pin 24 -> pin 16 gnd
pin 30 -> 7432 pin 6
pin 31+32 -> hole 28 5V


Attachments:
File comment: TAITO UNROM back
CAM01029.jpg
CAM01029.jpg [ 1.46 MiB | Viewed 1723 times ]
File comment: TAITO UNROM front
CAM01028.jpg
CAM01028.jpg [ 1.47 MiB | Viewed 1723 times ]
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 7 hours


Who is online

Users browsing this forum: No registered users and 1 guest


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group