It is currently Tue Dec 18, 2018 7:43 am

All times are UTC - 7 hours





Post new topic Reply to topic  [ 3 posts ] 
Author Message
PostPosted: Mon Dec 17, 2018 3:46 am 
Offline
User avatar

Joined: Sat Jul 04, 2015 9:58 am
Posts: 852
Location: -29.794229 -55.795374
Hi, I know that the best of the best way to fix a broken case (or should I say shell?) is to replace it, but what about the pirate ones wich are pretty different?
In this case, I finally could get a cartridge that's virtually equal to the one I had as a kid:
Attachment:
File comment: First time I saw it I tought it glowed in the dark!! :-)
20181215_085909.jpg
20181215_085909.jpg [ 627.98 KiB | Viewed 86 times ]

I tried to use some old notebook nuts and screws, carefully heating the plastic and making the nut go inside. But it only lasted a few days.
Superglue also didn't last long, in fact, it lasted even less than the nuts.
So, taking advice from an old member of this forum, Drakon, I decided to moderately try his methd in this case:
Attachment:
File comment: Not exactly like Drakon used to do, but close!
Not sure if it's a good or a bad thing...

20181215_085855.jpg
20181215_085855.jpg [ 619.96 KiB | Viewed 86 times ]

I added a generous amount of hotglue on the top, a little on the sides and in the middle.
I think there's some advantages of the easiness of removing it for maintenance, since hot glue seems to get out easily with isopropanol in case of necessity.

My doubts are:
1- How reliable is it?
It's working fine for a week of plugging and unplugging the cartridge, but I have no idea how long it will last.

2- If I use the same hotglue to keep the case closed, would it make too difficult to disassemble, in case of any neeeded maintenance in the future?

Thanks in advance.

Edit: Tried to make some things clearer.


Top
 Profile  
 
PostPosted: Mon Dec 17, 2018 10:53 am 
Offline

Joined: Sun Jun 12, 2011 12:06 pm
Posts: 450
Location: Poland
Yes, hot glue is good solution, but I never glue the PCB to the shell. Rather I glue some plastic parts to the shell that will help keep firmly the PCB inside shell place but with ability to remove it. (I like using old DC jacks sause they have cubic shape).

If the clips that hold both part of shell are broken, I just use transparent tape to keep both sides together.

Also, I recomment black hot glue instead of transparent - it is much harder and glues tighter. Dont forget to clean inside of cart with some alcohol to remove dust & dirt.


Top
 Profile  
 
PostPosted: Mon Dec 17, 2018 11:28 am 
Offline

Joined: Sun Apr 13, 2008 11:12 am
Posts: 7842
Location: Seattle
Low-temperature hot glue isn't particularly good at adhering to things other than itself, but it is excellently flexible.

The shell is almost certainly polystyrene or maybe ABS. An appropriate tape may sometimes help. I've recently tried using (very) hot air to reflow thermoplastics together: results have been mixed.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 3 posts ] 

All times are UTC - 7 hours


Who is online

Users browsing this forum: No registered users and 2 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group