It is currently Mon Nov 19, 2018 11:38 am

All times are UTC - 7 hours





Post new topic Reply to topic  [ 19 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: 220 in 1 dump
PostPosted: Sat Nov 10, 2018 9:31 am 
Offline

Joined: Fri Nov 09, 2018 2:02 pm
Posts: 10
I have purchased the Kazzo cartridge "INL Retro" Dumper-Programmer, and It seems to not working on my computer using the Anago wx software. However I have a problem dumping a copy of "220 in 1" Do anyone have some tips for how to do it? i have tryed every script and it didnt work. can anyone help my?


Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Sat Nov 10, 2018 1:36 pm 
Offline

Joined: Sun Jun 12, 2011 12:06 pm
Posts: 426
Location: Poland
Please provide good quality photos of PCB of your cartridge from both sides, there are no fortune-tellers.


Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Sat Nov 10, 2018 1:59 pm 
Offline

Joined: Fri Nov 09, 2018 2:02 pm
Posts: 10
Here i have the pictures from the pcb


Attachments:
20181110_215659.jpg
20181110_215659.jpg [ 2.2 MiB | Viewed 560 times ]
20181110_215620.jpg
20181110_215620.jpg [ 2.81 MiB | Viewed 560 times ]
Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Sat Nov 10, 2018 5:24 pm 
Offline

Joined: Sun Jun 12, 2011 12:06 pm
Posts: 426
Location: Poland
After briefly analyzing the PCB I would assume:
Code:
I would assume
[vmPPPPPPp] register ($8000-$ffff ?)
 |||||||||
 ||+++++++- 16K/32K PRG bank (p ignored in 16k mode)
 |+-------- mirroring (no idea if 0=V or 0=H)
 +--------- PRG mode (no idea if 0=16K or 0=32k)

so please write proper script for that.

* There is CHR-RAM but it is write-protected in some modes
* Does the cartridge contains UNROM Games (Contra?)
* There is reset detection circuitry so it need to be bypassed for the dumping (shorting or opening capacitor, depending on the connection which I don't see casue of bad light at bottom-right corner of top layer of cartridge - near the diode)


Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Sun Nov 11, 2018 1:20 am 
Offline

Joined: Fri Nov 09, 2018 2:02 pm
Posts: 10
There are on unrom games on it.
And here i have pic of the capacitor.


Attachments:
20181111_091559.jpg
20181111_091559.jpg [ 2.21 MiB | Viewed 504 times ]
Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Sun Nov 11, 2018 4:27 am 
Offline

Joined: Sun Jun 12, 2011 12:06 pm
Posts: 426
Location: Poland
So finally I think it is:
Image Image Image

Code:
  $8001      $8000        (mask: $8001)
[......wP]  [PmvPPPPp]
       ||    ||||||||
       |+----+||+++++- 16K/32K PRG bank (p ignored in 32k mode)
       |      |+------- PRG mode (0=32K,1=16K)
       |      +-------- mirroring (0=V,1=H)
       +--------------- 1=CHR-RAM is write protected
On power up & reset, both registers are cleared


In order to dump it, you need to
1) Short the capacitor
2) try this script (warning - I don't see in FCEUx source any mapper number that follows this description, so probably new mapper need to be assigned & emulator modified)
Code:
board <- {
  mappernum = 255,
  cpu_rom = { size_base = 2097152, size_max = 2097152, banksize = 0x4000 },
  ppu_rom = { size_base = 0, size_max = 0, banksize = 0 },
  ppu_ramfind = false, vram_mirrorfind = false
};

function cpu_dump(d, pagesize, banksize) {
  for (local i = 0; i < pagesize; ++i) {
    cpu_write(d, 0x8000, (i & 0x1F) | (1 << 5) | ((((i >> 5) & 1) << 7)));
   cpu_write(d, 0x8001, (i >> 6) & 1);
   cpu_read(d, 0x8000, banksize);
  }
}



Last edited by krzysiobal on Sun Nov 11, 2018 11:57 am, edited 1 time in total.

Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Sun Nov 11, 2018 9:18 am 
Offline

Joined: Fri Nov 09, 2018 2:02 pm
Posts: 10
It didnt work it say reader open error
And i have the capacitor shorting


Attachments:
20181111_171656.jpg
20181111_171656.jpg [ 1.38 MiB | Viewed 466 times ]
Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Sun Nov 11, 2018 12:00 pm 
Offline

Joined: Sun Jun 12, 2011 12:06 pm
Posts: 426
Location: Poland
I am not familiar with kazzo errors but maybe try the updated script above.
BTW. Does the cartridge with shorted capacitor works in console?


Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Sun Nov 11, 2018 12:08 pm 
Offline

Joined: Tue Feb 14, 2017 9:50 am
Posts: 95
roytje13 wrote:
It didnt work it say reader open error

That means anago is unable to communicate with the kazzo. Here are a few common cases: it is not connected properly, it is not set in the correct mode, it was not flashed with the original kazzo firmware or the software setup was not completed.
I'm assuming the drivers were not properly installed. You should attempt to follow INL guide again and making sure you do every step and that they are successful.
Also you might want to make sure you can dump some random generic game, like Super Mario Bros. (as NROM) before attempting anything else.


Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Mon Nov 12, 2018 9:24 am 
Offline

Joined: Fri Nov 09, 2018 2:02 pm
Posts: 10
MLX does it work on windows 10 64x


Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Mon Nov 12, 2018 9:35 am 
Offline

Joined: Tue Feb 14, 2017 9:50 am
Posts: 95
It should? I tested it on Windows 7 and Windows 8.1 it worked like a charm. I'm pretty sure you haven't properly installed the associated software/drivers.


Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Mon Nov 12, 2018 10:00 am 
Offline

Joined: Fri Nov 09, 2018 2:02 pm
Posts: 10
i have super mario bros 3 (pal)
i reinstaled the drivers and it didnt work
wat should i do?


Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Mon Nov 12, 2018 10:42 am 
Offline

Joined: Tue Feb 14, 2017 9:50 am
Posts: 95
Try another computer? Does your kazzo has a switch? Which position is it in?


Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Mon Nov 12, 2018 12:01 pm 
Offline

Joined: Fri Nov 09, 2018 2:02 pm
Posts: 10
its on run pos.
i have an other pc with win 98


Top
 Profile  
 
 Post subject: Re: 220 in 1 dump
PostPosted: Mon Nov 12, 2018 12:28 pm 
Offline

Joined: Fri Nov 09, 2018 2:02 pm
Posts: 10
I can try to run it on vurtual windows xp


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 19 posts ]  Go to page 1, 2  Next

All times are UTC - 7 hours


Who is online

Users browsing this forum: No registered users and 5 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group