TV-NET MC-1200

Discuss hardware-related topics, such as development cartridges, CopyNES, PowerPak, EPROMs, or whatever.

Moderators: B00daW, Moderators

Post Reply
Fiskbit
Posts: 182
Joined: Sat Nov 18, 2017 9:15 pm

TV-NET MC-1200

Post by Fiskbit » Thu Mar 26, 2020 4:37 am

I just picked up a TV-NET modem and figured I'd post some pictures of its PCB, since I don't think there are any online yet. This is the MC-1200 version; I have an MC-1200B coming later for comparison, and there's also an MC-1200A and a TV-NET Rank 2 MC-4800.

The TV-NET carts have a footprint exactly the size of a credit card and are about 0.1" thick. For the connector, rather than one long slot containing an edge connector, it has one hole per pin. The cart I have on-hand is SanrainF-III (Sun-Line F-III?). Video of the F-II in actual use can be seen in this commercial. I don't know how the F-II and F-III differ. The top of my cart has a lockable slot that presumably contains a removable battery, but I've not removed it in case there is still data saved on the cart.

A bunch of pictures of the exterior and some information can be found on this blog post: http://jironosuke.cocolog-nifty.com/blo ... -f3a6.html.
Attachments
TV-NET-pcb-1.jpg
TV-NET-pcb-2.jpg
TV-NET-pcb-3.jpg
TV-NET-pcb-4.jpg
TV-NET-cart-connector.jpg

lidnariq
Posts: 9697
Joined: Sun Apr 13, 2008 11:12 am
Location: Seattle

Re: TV-NET MC-1200

Post by lidnariq » Thu Mar 26, 2020 11:34 am

Quickly enumerating the ICs I see:
* Sony CXK5816SP-12L ( 2048x8 SRAM )
* Hitachi S256KP-12 ( unknown. maybe an EEPROM? )
* NEC D23C1000C-1 ( 131072x8 Mask ROM )
* NEC D65013GF503 ( uncommitted gate array )
* Sharp PC814 ( optoisolator )
* Sierra Semiconductor SC11007CV ( baud rate generator )
* Sierra Semiconductor SC11014CV ( 300/1200 baud modem )
* NEC C251C ( op amp )
* TDK RZCO5N50 ( boost converter )
* Mitsubishi M74ALS02P ( quad NOR gate )
* ?? TV-NET MC/BS.P256-01 ( mask ROM )
* 3x Samsung KS74HCTLS157N ( quad 1-of-2 multiplexer - "HCTLS", really??? )

Fiskbit
Posts: 182
Joined: Sat Nov 18, 2017 9:15 pm

Re: TV-NET MC-1200

Post by Fiskbit » Sat Apr 04, 2020 7:03 pm

I received a MC-1200B, TV-NET controller, and TV-NET JRA-PAT cart. Pictures of the MC-1200B PCB are attached. The chip in the first picture that isn't very readable says: NEC JAPAN, D65013GF503, 8840KK001.
Attachments
MC-1200B-pcb-1.jpg
MC-1200B-pcb-2.jpg
MC-1200B-pcb-3.jpg
MC-1200B-pcb-4.jpg
MC-1200B-pcb-5.jpg

Fiskbit
Posts: 182
Joined: Sat Nov 18, 2017 9:15 pm

Re: TV-NET MC-1200

Post by Fiskbit » Sat Apr 04, 2020 7:05 pm

The TV-NET controller is a pad with 21 buttons and a switch on the back that is recessed enough that it can't be flipped by hand. I've included a picture below from this Twitter post showing 4 different kinds of this controller; mine is the basic TV-NET version on the left. My guess is that they're all functionally the same and just have different labeling. Unfortunately, while the controller has screws, it's also held together by interior plastic tabs that I've been unable to release. If I figure out how to open it nondestructively, I'll add pictures of the PCB.

Using lidnariq's raw.nes input test (which does a strobe on $4016.0), I've found that the controller has a 24-bit report on $4017.1 and returns 1's for any additional reads. Each button's report appears to be independent; there doesn't seem to be a limit or any ghosting. The bits come in the following read order (using the labeling on the standard TV-NET variant):

0: P/T switch (1 if T)
1: 終了 (Shuuryou / End)
2: F3
3: (Always 1)
4: F1
5: F2
6: F4
7: F5
8: 1
9: 4
10: 7
11: (Always 1)
12: 2
13: 3
14: 5
15: 6
16: *
17: Left
18: 実行 (Jikkou / Run)
19: Right
20: 8
21: 9
22: 0
23: .
Attachments
TV-NET Controllers.jpg
TV-NET-controller-1.jpg
TV-NET-controller-2.jpg

krzysiobal
Posts: 759
Joined: Sun Jun 12, 2011 12:06 pm
Location: Poland

Re: TV-NET MC-1200

Post by krzysiobal » Thu Sep 24, 2020 2:05 am

Thanks to Ben Boldt I was able to obtain TV-NET too, so prepare soon for rev-en. Unfortunatelly my unit does not came with the credit cart, so after I figure out how it is accessed by the console, I'd ask for help to dumping its content.

To open the controller, you have to squeeze (using clamp) the top part in the middle and lever it up using some plastic lever.

Image Image Image Image Image Image Image Image Image

Post Reply